COORD3 HORIZONTAL ARM CMM Products

COORD3 manual & DCC air bearing bridge configuration CMMs offer advanced measuring platforms. Available in bridge widths from 400mm to 2000mm and offering the most comprehensive range of CMM models sizes in the market to accommodate your specific measurement requirements. Bridge CMMs can be equipped with Renishaw touch/scanning probes and Perceptron laser scanning sensors suitable for all measuring applications.
SWAN SI HORIZONTAL ARM CMM – TABLE MOUNT
The COORD3 SWAN SI series of table mounted (Console) horizontal arm coordinate measuring machine offers a technically advanced and cost effective solution for the dimensional inspection of thin-walled sheet metal and plastic components typical of the automotive industry.
The SWAN is unique in offering air bearings to both Y and Z axis providing a high performance high accuracy solution. The X axis guide-way is located on the side of the machine cast iron or granite support table and allows the arm to be moved outside of its measuring volume for part loading. SWAN SI can be installed on pneumatic vibration isolation system for installation in production applications without the need for a dedicated machine foundation.
Modular in design SWAN SI is available in a range of standard cross section sizes (ZY):
15.12 | 18.12 | 20.12 | 15.15 | 18.15 | 20.15 | 20.16 | 25.16 | 30.16 Accuracy from 12 + 15L/1000 <40
- Table based models in single or twin arm configuration
- Manual and DCC models with optional disengageable drives available
- Granite or cast iron surface plate
- Steel X guideway
- Rugged machine construction for reliable operation in manufacturing environments
- 0.1 micron resolution measuring scales incorporating dynamic signal processing
- Highest accuracy in industry
- Precision roller bearings on X axis
- Rigid air bearings to Y and Z axes with wide bearing spread ratios and low air consumption
- Open access to CMM measuring area from all sides
- Suitable for a shop floor environment
- Maximum Positioning Speed 520mm/sec
- Maximum Acceleration 850mm/sec2
COORD3 SWAN Horizontal Arm Table mount CMMs are available with the following measuring strokes:
- X axis strokes: 2000 | 3000| 4000 | 5000 | 6000 | 8000
- Y axis strokes*: 1200 | 1500 | 1600
- Z axis strokes: 1500 | 1800 | 2000 | 2500 | 3000
*Per arm measuring stroke. Dual machine arms overlap by 100mm per arm
MPEP from 12 microns
MPEE from 12 + 15L/1000 ≤ 40
Environment
- Nominal Temperature 20 °C
- Allowable Temperature Range: 18 – 22 °C
- Temperature Gradient: 0.5° C/hour – 2° C/day – 0.5° C/meter
- Extended Temperature Range: 16 – 26 °C
- Operating Temperature Range: 15 – 35 °C
- Relative Humidity 40 – 80% (non condensating)
- Acceptable Vibrations: 30mm/ sec2 1-10Hz | 15mm/ sec2 10-20Hz | 50mm/ sec2 20-100Hz
Services
- Air Consumption 110Nl/min
- Power Supply Voltage 230v 50Hz or 110v 60Hz (+/- 2% single phase)
- Maximum Power Consumption 10A 1400W
- Minimum Air Supply 5.5 Bar -80PSI
Performance Data
- All COORD3 CMM products are evaluated for accuracy using the ISO10360 standard.
- Laser Scanning Sensor
- Disegageable drives on DCC models allowing manual operation
- Dynamic Wireless Thermal Compensation of Machine and Part
- Protection Bellows Covers to Y & Z axes
- Renishaw PHS infinite position probe head
- Cast Iron or Granite Table
- Table with threaded holes or T slots
- Air Drier
- Modular Part Fixturing Kits
- CMM Touch Station
- CMM Modular Enclosure
SWAN DUAL ARM HORIZONTAL ARM CMM
The COORD3 SWAN DUAL ARM series of table (Console) and rail mounted (Runway) horizontal arm coordinate measuring machines offer a technically advanced and cost effective solution for automotive car body-in-white and sub-assemblies.
The rail model allows the full machine to be installed flush with the factory floor with walkable way covers.
The SWAN is unique in offering air bearings to both Y and Z axis providing a high performance high accuracy solution. Each horizontal arm measuring volume overlaps by 100mm allowing for full cross-body measurements.
Modular in design SWAN Dual Arm CMMs are available in a range of standard cross section sizes (ZY):
20.30 | 25.30 | 30.30 | 25.34 | 30.34
Accuracy from 12 + 15L/1000 <40
- Twin arm able or rail model configuration
- Manual and DCC models with optional disengageable drives available
- Granite or cast iron surface plate
- Steel X guideway
- Rugged machine construction for reliable operation in manufacturing environments
- 0.1 micron resolution measuring scales incorporating dynamic signal processing
- Highest accuracy in industry
- Precision mechanical bearings on X axis
- Rigid air bearings to Y and Z axes with wide bearing spread ratios and low air consumption
- Walk-on X axis covers for optimal safety
- Open access to CMM measuring area from all sides
- Suitable for a shop floor environment
- Maximum Positioning Speed 520mm/sec
- Maximum Acceleration 1500mm/sec2
COORD3 SWAN Dual Horizontal Arm CMMs are available with the following measuring strokes:
- X axis strokes: 4000 | 5000 | 6000 | 8000 | 10000
- Y axis strokes*: 1500| 1600)
- Z axis strokes: 2500 | 3000
*Per arm measuring stroke. Dual machine arms overlap by 100mm per arm
MPEP from 12 microns
MPEE from 12 + 15L/1000 ≤ 40
Environment
- Nominal Temperature 20 °C
- Allowable Temperature Range: 18 – 22 °C
- Temperature Gradient: 0.5° C/hour – 2° C/day – 0.5° C/meter
- Extended Temperature Range: 16 – 26 °C
- Operating Temperature Range: 15 – 35 °C
- Relative Humidity 40 – 80% (non condensating)
- Acceptable Vibrations: 30mm/ sec2 1-10Hz | 15mm/ sec2 10-20Hz | 50mm/ sec2 20-100Hz
Services
- Air Consumption 110Nl/min
- Power Supply Voltage 230v 50Hz or 110v 60Hz (+/- 2% single phase)
- Maximum Power Consumption 10A 1400W
- Minimum Air Supply 5.5 Bar -80PSI
Performance Data
- All COORD3 CMM products are evaluated for accuracy using the ISO10360 standard.
- Laser Scanning Sensor
- Disegageable drives on DCC models allowing manual operation
- Dynamic Wireless Thermal Compensation of Machine and Part
- Protection Bellows Covers to Y & Z axes
- Renishaw PHS infinite position probe head
- Cast Iron or Granite Table on Console model
- Seperate Table on Runway model
- Air Drier
- Modular Part Fixturing Kits
- CMM Touch Station
- CMM Modular Enclosure
SWAN L HORIZONTAL ARM CMM – RAIL MOUNT
The COORD3 SWAN L series of rail mounted (Runway) horizontal arm coordinate measuring machine offers a technically advanced and cost effective solution for the dimensional inspection of thin-walled sheet metal and plastic components typical of the automotive industry.
The rail allows the machine to be installed flush with the factory floor with walkable way covers allowing inspection of large heavy parts either supported on a separate table, floor mounted fixture of automation system.
The SWAN is unique in offering air bearings to both Y and Z axis providing a high performance high accuracy solution.
Modular in design SWAN L is available in a range of standard cross section sizes (ZY):
15.12 | 18.12 | 20.12 | 15.15 | 18.15 | 20.15 | 20.16 | 25.16 | 30.16
Accuracy from 12 + 15L/1000 <40
- Rail based models in single or twin arm configuration
- Manual and DCC models with optional disengageable drives available
- Optional granite or cast iron independent surface plate
- Steel X guide-way rail
- Rugged machine construction for reliable operation in manufacturing environments
- 0.1 micron resolution measuring scales incorporating dynamic signal processing
- Highest accuracy in industry
- Precision mechanical bearings on X axis
- Rigid air bearings to Y and Z axes with wide bearing spread ratios and low air consumption
- Walk-on X axis covers for optimal safety
- Machine can be flush floor mounted
- Open access to CMM measuring area from all sides
- Suitable for a shop floor environment
- Maximum Positioning Speed 520mm/sec
- Maximum Acceleration 850mm/sec2
COORD3 SWAN Horizontal Arm Rail mount CMMs are available with the following measuring strokes:
- X axis strokes: 2000 | 3000| 4000 | 5000 | 6000 | 8000
- Y axis strokes*: 1200 | 1500 | 1600
- Z axis strokes: 1500 | 1800 | 2000 | 2500 | 3000
*Per arm measuring stroke. Dual machine arms overlap by 100mm per arm
MPEP from 12 microns
MPEE from 12 + 15L/1000 ≤ 40
Environment
- Nominal Temperature 20 °C
- Allowable Temperature Range: 18 – 22 °C (Extended 16 – 26 °C)
- Temperature Gradient: 0.5° C/hour – 2° C/day – 0.5° C/meter (Extended Range 5° C/day – 1.0° C/meter)
- Operating Temperature Range: 15 – 35 °C
- Relative Humidity 40 – 80% (non condensing)
- Acceptable Vibrations: 30mm/ sec2 1-10Hz | 15mm/ sec2 10-20Hz | 50mm/ sec2 20-100Hz
Services
- Air Consumption 110Nl/min
- Power Supply Voltage 230v 50Hz or 110v 60Hz (+/- 2% single phase)
- Maximum Power Consumption 10A 1400W
- Minimum Air Supply 5.5 Bar -80PSI
Performance Data
- All COORD3 CMM products are evaluated for accuracy using the ISO10360 standard.
- Laser Scanning Sensor
- Disegageable drives on DCC models allowing manual operation
- Dynamic Wireless Thermal Compensation of Machine and Part
- Protection Bellows Covers to Y & Z axes
- Renishaw PHS infinite position probe head
- Separate Cast Iron or Granite Table
- Air Drier
- Modular Part Fixturing Kits
- CMM Touch Station
- CMM Modular Enclosure
JUPITER INSPECTION ROBOT
The JUPITER INSPECTION ROBOT offers a high performance shop-hardened CMM for use in direct production pace manufacturing and specifically developed for the inspection of automotive body-in-white and sub assemblies.
Jupiter is a Runway configuration, available in single or dual arm configuration, and is fully encapsulated to provide thermal isolation from environmental changes and includes protection from shop-floor contamination. Jupiter is characterized by high dynamics and high accuracy. The Jupiter CMM can be installed flush with the factory floor with walkable way covers as standard.
Jupiter is unique in offering air bearings to both Y and Z axis providing a high performance high accuracy measuring solution. Each horizontal arm measuring volume overlaps by 100mm to allow for full cross-body measurements.
Modular in design JUPITER is available in the following cross sections (ZY):
Single Arm: 20.16 | 25.16 | 30.16 | 20.18 | 25.18 | 30.18
Dual Arm: 20.30 | 25.30 | 30.30 | 25.34 | 30.34
Accuracy from 12 + 15L1000 <40
- Rail based models in single or twin arm configuration
- Optional cast iron independent surface plate
- Steel X guide-way rail
- Rugged machine construction for reliable operation in manufacturing environment
- 0.1 micron resolution measuring scales incorporating dynamic signal processing
- Highest accuracy in industry
- Precision mechanical bearings on X axis
- Rigid air bearings to Y and Z axes with wide bearing spread ratios and low air consumption
- Walk-on X axis covers for optimal machine operation and safety
- Machine can be flush floor mounted
- Open access to CMM measuring area from all sides
- Suitable for a shop floor environment
- Maximum Acceleration 1500mm/sec2
- Maximum Positioning Speed 520mm/sec
COORD3 JUPITER Horizontal Arm CMMs are available with the following measuring strokes:
- X axis strokes: 4000 | 5000 | 6000 | 8000 | 10000 |12000
- Y axis strokes*: 1600| 1800
- Z axis strokes: 2500 | 3000
*Per arm measuring stroke. Dual machine arms overlap by 100mm per arm
MPEP from 12 microns
MPEE from 12 + 15L/1000 ≤ 40
Environment
- Nominal Temperature 20 °C
- Allowable Temperature Range: 18 – 22 °C
- Temperature Gradient: 0.5° C/hour – 2° C/day – 0.5° C/meter
- Extended Temperature Range: 16 – 26 °C
- Operating Temperature Range: 15 – 35 °C
- Relative Humidity 40 – 80% (non condensating)
- Acceptable Vibrations: 30mm/ sec2 1-10Hz | 15mm/ sec2 10-20Hz | 50mm/ sec2 20-100Hz
Services
- Air Consumption 150Nl/min
- Power Supply Voltage 230v 50Hz or 110v 60Hz (+/- 2% single phase)
- Maximum Power Consumption 10A 1400W
- Minimum Air Supply 5.5 Bar -80PSI
Performance Data
- All COORD3 CMM products are evaluated for accuracy using the ISO10360 standard.
- Laser Scanning Sensor
- Dynamic Wireless Thermal Compensation of Machine and Part
- Protection Bellows Covers to Y & Z axes
- Renishaw PHS infinite position probe head
- Separate Component Support Table
- Automatic Part Loading systems
- Air Drier
- Modular Part Fixturing Kits
- CMM Touch Station